Page 361 - VSI Master Catalog

REMOTE, LARGE DIAMETER
OIL FILTER MOUNT
• Compact, low-profile design that facilitates
OIL FILTER BYPASS PLATE
installation in crowded areas.
• Made from 6061-T6 billet aluminum and
• Fits SBC & BBC (Mark IV).
• Aluminum bypass replaces engine- mounted oil filter in wet sump oiling
anodized blue to resist corrosion.
• Includes two screw-in adapters to cover
filter or oil cooler.
• Drilled and tapped for 1/2” NPT inlet and outlet fittings. • Includes all mounting hardware, gaskets and O-ring.
MOR23770 Oil Filter Bypass
BILLET BYPASS PLATE
• Fits World Products Merlin Big Block or standard Small Block and Big Block (Mark IV) Chevy applications without bolt hole at center of filter pad.
• Needed when using a remote oil filter or returning oil from dry sump oiling system.
• Sealing washers are captured in the plate for tight seal against block surface, are installed under bolt heads for leak-free performance.
• Drilled and tapped to accept -10 AN fittings. • Includes all mounting hardware and O-rings.
most large-diameter style oil filters.
• -12 AN inlet and outlet threaded fittings that
are positioned vertically to improve laminar flow. MOR23766 Billet Aluminum Oil Filter Mount
system and directs oil to remote oil
REMOTE OIL FILTER MOUNTS, 1/4” NPT
• Gives you the freedom to mount your oil filter in an easier place to access.
• Made of billet aluminum and are tapped for 1/4” NPT on both the inlet and outlet.
• Center port can be used for an oil pressure or temperature gauge.
MOR23763 MOR23764
Side Port Style, Blue Front Port Style, Black
OIL BYPASS ELIMINATOR, CHEVY
• Eliminate the oil bypass found on Chevrolet engines.
• Does not allow unfiltered oil back into the engine.
• Stock type spin-on oil filter can be used with this part installed.
• Machined from billet aluminum.
• Single inlet and easy two bolt installation.
MOR23782
Billet Bypass Plate
MOR23775
SBC, BBC (except Gen V and Gen VI)
OIL FILTER BLOCK-OFF PLATES
• For Moroso Dry Sump Oiling System or External Oil Pump.
• Drilled and tapped to accept 1/2”
NPT fitting to provide increased
clearance for installing input pressure line.
• Includes all mounting hardware and O-rings.
MOR23840 MOR23820
OIL ACCUMULATOR
• Provides emergency supply of oil under pressure instantly when needed.
OIL FILTER ADAPTERS
• For Small Block Chevy engines without modifications & Big Block Mark IV Chevy engines with minor block modifications.
• Eliminates need for a remote oil filter and associated plumbing hardware.
• Standard spin-on filter attaches to bottom.
• Lowers oil filter by 1-1/2”.
• Equipped with 1/2” NPT inlet and outlet ports.
SBC and BBC (exc. Gen V and Gen VI) without Bolt Hole at Center of Pad
57-01 Ford 8, 6, 4 cyl; 1959-03 Dodge; Chrysler 8, 6, 4, cyl; Others: All Engines with 2-1/2” I.D.
MOR23690 MOR23692
For Plumbing Accumulators and External or Dry Sump Oil Pumps
For Plumbing Remote Oil Coolers
• Air Pressure gauge verifies accumulator is ready for use. • Cold start valve releases oil into cold engine for
x 2-7/8” O.D. Sealing Area and 3/4” -16 UNF Block Thread. -12 AN fitting size
OIL FILTER ADAPTER, 4.6/5.4 FORD
• Anodized adapter replaces larger
reduced wear.
• Tapped for 1/2” NPT fitting.
• Can be mounted in any position using Moroso
factory casting.
• Enables plumbing of external, wet or dry
MOR23900 MOR23901 MOR23902
3 qt. Capacity, 20-1/8” x 4-1/4” Cylinder 1.5 qt. Capacity, 10” x 4-1/4” Cylinder
3 qt. Capacity, 23” x 4-3/4” Cylinder
sump oil pumps when lower port is plugged.
• -16 AN fitting supplied for water outlet to radiator.
• Includes (2) -10 AN to -12 AN fittings for oil line plumbing
and (1) -10 AN Plug.
MOR23681 Oil Filter Adapter, 4.6/5.4L Ford
accumulator mounts.
359