Page 428 - VSI Master Catalog

Dis-4 harnesses
• These harnesses will provide a splice-free installation of
a DIS Ignition.
MSD88812 MSD DIS-4 to Dual Ford Coil Packs MSD8883 MSD DIS-2/4 to Dodge/Mitsubishi
6-heMi harnesses
packs
rPM MoDule PacKs
• Each Module Pack has 5 modules within a range of 1000 RPM.
• Used for all MSD Soft Touch Rev Control, 6, 7, and 8 Series Ignitions.
• 50-State Legal via E.O. #D-40-29!
rPM range
MSD8743 3000, 3200, 3400, 3600, 3800 MSD87431 3100, 3300, 3500, 3700, 3900 MSD8744 4000, 4200, 4400, 4600, 4800 MSD87441 4100, 4300, 4500, 4700, 4900 MSD8745 5000, 5200, 5400, 5600, 5800 MSD87451 5100, 5300, 5500, 5700, 5900 MSD8746 6000, 6200, 6400, 6600, 6800 MSD87461 6100, 6300, 6500, 6700, 6800 MSD8747 7000, 7200, 7400, 7600, 7800 MSD87471 7100, 7300, 7500, 7700, 7900 MSD8748 8000, 8200, 8400, 8600, 8800 MSD87481 8100, 8300, 8500, 8700, 8900 MSD8749 9000, 9200, 9400, 9600, 9800 MSD97491 9100, 9300, 9500, 9700, 9900
MSD8750 10000, 10200, 10400, 10600, 10800
MSD8751 11000, 11200, 11400, 11600, 11800
MoDule holDer
• Stores your MSD RPM Modules in a neat order, and is handy on the pits or in the race car for quick access to change
RPM limits.
• Chrysler used two different coil on the late model Hemi engines. • For connections on a carbureted
engine a Harness will be required. • For EFI engines, the Harness and
an Adapter will be required.
MSD88863 MSD88864 MSD88816
03-05 Harness
06-08 Harness
06-08 Adapter for Factory EFI
tach aDaPter
• For use when installing an MSD 5, 6, 7, Series ignition and your factory tachometer or some aftermarket tachometers that are not reading properly due to an incorrect triggering signal.
• These adapters cure this problem.
MSD8910 Tach Adapter, with Points Distributor or Amplifier MSD8920 Tach Adapter, with Magnetic Pickup Distributor MSD8910EIS Tach Adapter, with Electronic Ignition System
tach sPlitter
• Allows the use of two tachometers factory and aftermarket.
• Splits the wire between the tachoutput wires and your MSD Ignition and the tach.
MSD8911 Tach Splitter
MoDule selectors
• The Two-Step Module allows you to switch between two different RPM or ignition retard modules when used with a MSD soft Touch Rev Control or Timing Computer.
• The Three-Step adds an additional stage that is perfect to control burnout RPM.
• Uses MSD RPM Modules or RPM Module Selectors.
MSD8739 Two-Step Selector MSD8737 Three-Step Selector
aDjustaBle loW rPM MoDule
• Plugs directly into a Soft Touch Rev Control, Two-Step Module Selector,
RPM Activated Switch and MSD Shift Light.
• Lets you select any RPM between 1000 and 3000 RPM by turning a screw.
• Great for automatic cars using a Two-Step Module Selector when leaving the starting line below 3000 RPM.
MSD8677 Adjustable Module 1000-3000 RPM
426
MSD87551
Module Holder, Rubber
rPM WinDoW sWitch
• Enables you to activate and deactivate a circuit at adjustable RPM points.
• Handles up to 1.5 amps.
• Uses RPM Plug-In Modules.
MSD8956 RPM Window Switch
rPM actiVateD sWitch
• Can be used in a variety of applications like nitrous solenoids, air shifters, shift lights, or anything that needs to be turned on at specific RPM.
• Uses RPM Plug-In Modules.
MSD8950 RPM Activated Switch for Standard Ignitions
Digital rPM WinDoW sWitch
• Will accept an input RPM signal
from a coil negative terminal
(for stock ignitions), a tach output
from an ignition control, an ECU
tach output or even a 5 volt tach signal.
• No RPM modules are needed, RPM
activation points are programmed by simply scrolling through the LED display to your desired RPM amounts.
• Programmable from 200 RPM to 15,000 RPM in 100 RPM increments.
MSD8969 MSD Digital RPM Window Switch