Page 427 - VSI Master Catalog

sYnchroniZation PicKuP Kits
• Spark plug wire sync kit, installs
to the number one spark plug wire.
• Cam Gear Sync kit is supplied with a non-magnetic pickup, connectors and the magnet and retainer.
MSD7555 Spark Plug Wire Sync Kit MSD2345 Chevy V8, Adjustable MSD23451 Chevy V8, Hall-Effect MSD2346 Univ. Cam Sync Pickup Kit MSD2348 Hall Effect w/ LED
ForD launch Master-2 steP
• Connects right to your late model Ford to produce consistent launches and quicker 60-foot times.
• Easily set a launch RPM for consistent holeshots.
• Connects to the factory coils for easy installation.
• The best way to launch hard.
MSD8731 2-Step, 2011 5.0L Mod Motors MSD8734 2-Step, Ford 4.6L Mod Motors
ls 2-steP launch control
• The unit is easy to connect with factory style connectors and lets the users
set an RPM limit to activate from
the holeshot!
• When you’re staged, you can hold the pedal to the floor while the RPM stays at a consistent level producing consistent holeshots.
MSD8733 LS 2-Step Launch Control
lsx trigger conVerter
• Plugs into the factory crank sensor of an LS1/LS2 engine and converts
the factory trigger signal into a 12 volt square wave signal to trigger an MSD Ignition Control such as a 6 or 7-Series Ignition control.
• For racers that are incorporating a front mount distributor to their LS engines.
MSD6301 LSx Trigger Converter
terMinal striPs
Dual channel ignition aDaPter
• Simulates the original coil trigger signal allowing the ECU to properly trigger both tachometer and fuel injection with the MSD DIS
Ignition installed.
• If your vehicle does not start after
the installation of an MSD DIS-2 or DIS-4 you may need this Dual Channel Adapter.
MSD8912 Dual Ignition Adapter
coil interFace MoDule
• These modules go between the factory GM ignition module and coils. • Color coded wires that connect to the
DIS wiring.
• Molded Rynite is used for its dielectric strength. • Connects directly to the factory terminals.
MSD8870 Coil Interface Module
DistriButorless tach DriVer
• Wires inline to the coils shared 12 volt supply.
• It senses the current through this
wire and converts this to a signal
that most aftermarket tachometers
and RPM devices use as a trigger signal.
MSD8913 Distributorless Tach Driver Not for Use on LS1 MSD8918 Tach Signal GMR Pickup
launch control MoDule selector
• This unit allows you to make adjustments in 100 RPM increments from the driver’s seat.
• Compact size: 1.5” x 3.5” x 2”
• Increased protection against EMI.
• Launch Control features two other RPM limits;
• These terminal strips can be used for virtually any wiring installation to provide a clean, professional appearance.
MSD8735 Launch Control Module Selector 6, 7 Series
Wiring harnesses & aDaPters
• Designed the plug-in directly into the factory harness of your factory coil and have the corresponding MSD color coded wires plug directly into the MSD harness.
• No cutting or splicing!
MSD8860 6’ Cable Harness, 2 Wire Magnetic Trigger
MSD8861 GM HEI Module bypass cable for 6, 7 Ignitions
MSD8862 6’-shielded 2-Wire Mag trigger to MSD 6 or 7 Ignitions
MSD8869 4” Ford Dura-spark to MSD 6 or 7 Ignitions MSD8874 MSD to Ford TFI Harness
MSD8876 MSD to GM Dual Connector Coil
MSD8877 MSD to GM ‘96-On Single Connector Coil
• Four separate terminals to hold 12-gauge or smaller wires. MSD8810 Terminal Strips
one top end and over rev protection for water burnouts.
425