Page 372 - VSI Master Catalog

VALVE SEAT PRESSURE TESTER
• For Professional engine builders for on the head spring pressures between rounds for a quick-check on spring pressures.
• The “Gripper” machined billet aluminum T-Handle designed by Jerry Haas.
• Scale reading from 160 to 400 lbs.
• Rocker arm stud mount.
SPARK PLUG TOOLS
LIGHTED MAGNIFIER
• Designed with Coaxial illumination to provide a wide area illumination and a bright, narrow light beam straight down.
• Allows clear viewing of surface details to bottom of small holes.
• 3.8x magnification provides greater depth of field. MOR62347 Lighted Magnifier
MAGNIFYING FLASHLIGHT
MOR62390 MOR62391 MOR62388 MOR62389
300 lb Valve Spring Tester (Standard) 160-400 lb Low Profile Valve Spring tester 400 lb Valve Spring Tester (Standard) Low-Profile Valve Seat Pressure Tester
FENDER COVER
• 34” x 22” Rubber cover printed with Moroso and Competition Engineering Logos.
• Non-skid foam backing is safe for your car’s finish and will not slide off while working.
• Acid and grease resistant, top surface is easily washable with mild solvents or detergents.
MOR99406 Fender Cover
CARBURETOR WORK STAND
• Designed to hold Quadrajet and
both standard and spread-bore
Holley carbs, this tool greatly simplifies carburetor work.
• Manufactured of cast aluminum
with open center and mounting pegs.
• 6.4x fire polished, B1-convex optic lens. • Powerful white light LED floods
MOR62070
JET TOOL
• Designed with a stronger, fully machined tip that slides over jet, holding it firmly in place.
• Short design, sure-grip handle simplifies jet removal and installation in crowded engine compartments.
• Fits all Holley round-head type carb jets. MOR62293 Jet Tool
POWER VALVE TESTER
• CNC-machined from billet aluminum and blue anodized for durability.
• The testers feature a cut-away section where you can visually inspect the operation of the power valve.
• They require the use of a hand-operated vacuum pump to function correctly.
accurate inspections.
• Lower voltage for longer battery life.
• Easy one-handed on/off switch.
• Black anodized billet aluminum flashlight housing. • 2 AA batteries included.
MOR62348 Magnifying Flashlight, LED
SPARK PLUG INDEXER
• Designed for both flat and taper-seat 14mm spark plugs.
• With their hex head design, it makes them easy to be held in a vise.
MOR62160 Spark Plug Indexer
WIRE STRIPPING TOOL
• Provides secure, factory quality crimps everytime.
• Strip wires without damaging the conductor.
Carburetor Work Stand
the insulator cavity with light for
MOR62295
Holley Carburetor Power Valve Tester
• Makes adjusting coil-over shocks much easier. • Works with C/E, AVO, HAL, Koni, Bilstein,
CARBURETOR DRAIN CUP
• Uses a special channeled handle to catch dripping fuel and direct it into the holding cup.
MOR65805 Carburetor Drain Cup
shocks with adjusting nuts up to 3-1/4” diameter. • Manufactured of cast steel with finger indents for
MOR62270
Wire Stripping Tool, 8mm
WIRE CRIMPING TOOLS
• Cuts, strips, and crimps park plug wire terminals when custom fitting Spark plug wires and has other general-purpose uses.
MOR62260 MOR62268
General Purpose Wire Crimper Super-duty Wire Crimping Tool
SUSPENSION TOOLS
COIL-OVER SHOCK ADJUSTING TOOL
Carrera, QA1, Monroe and most other coil-over
370
sure grip operation.
MOR62030 Coil-Over Shock Adjusting Tool