Page 513 - VSI Master Catalog

10-BOLT 8.2" CHEVY
• 8.20” ring gear diameter, 1.438’’ pinion diameter, 17 spline pinion, 10-bolt housing, 11 5/16 oval housing.
• Fits: 55-64 Chevrolet, 55-62 Corvette
*Fits 3.08 to 3.70 Carrier, ** Fits 4.11 to 4.56 Carrier.
12-BOLT 8.5", ”O” AXLE
• 1.626’’ Pinion Diameter, 27 Spline Pinion, Irregular 12 bolt hole cover, 10-bolt, “O” Axle, 2.93 to 3.23 ratio carrier.
Part# Ratio Street Gears *RIC49-0052-1 3.55 *RIC49-0099-1 3.73 Street/Strip Gears **RIC69-0163-1 4.11 **RIC69-0022-1 4.56
Teeth
39-11 41-11
37-9 41-9
• Fits 68-70 Cutlass, 442.
Part# Ratio Street Gear RIC49-0049-1 3.42 RIC49-0050-1 3.90
CAMARO 2010-UP
Part# Ratio
Teeth
41-12 39-10
Teeth
41-11 41-10
12-BOLT 8.875" TRUCK
• 8.875’’ diameter ring gear, 1.438’’ pinion diameter, 30 spline pinion, irregular 12 bolt hole cover,.
Street/Strip Gear
RIC49-0187-1 RIC69-0492-1
3.73 4.10
• 3-Series fits 3.40 and numerically lower ratio carrier.
• 4-series fits 3.73 and numerically higher carrier.
• Fits: 64-82 Blazer/C10 & K10 rear/K20 rear (Note: Will not
fit 2.56 & 2.73 carrier on 80-83 Truck and Blazer.), 69-81 G10 & G20 Van.
57-64 OLDS 9.3" “C” AXLE
• 9.30” ring gear diameter, 1.625’’ pinion diameter, 13 spline Pinion, “C” axle only.
• 3.23 and higher must be replaced with 4.10 higher carrier. • Fits: 57-64 Oldsmobile, 57-64 Pontiac.
Part# Ratio
Street Gear
RIC49-0068-1 3.08
RIC49-0070-1 3.42
RIC49-0072-1 3.73
RIC49-0280-1 3.73
Street/Strip Gear
RIC69-0204-1 4.10
RIC69-0350-1 4.10
RIC69-0-206-1 4.56
RIC69-0352-1 4.56
RIC69-0298-1 4.88
RIC69-0300-1 5.13
*Special Cross Shaft Pin Required RIC80-0269-1
When installing 5.13 and 5.38 ratios, differential pin P/N 80-0269-1 must be used.
12-BOLT 8.875" PASSENGER
Teeth Carrier
40-13 3 41-12 3 41-11 3 41-11 4
Part# Street/Strip Gear RIC69-0006-1 RIC69-0008-1 RIC69-0358-1
Ratio Teeth
4.10 41-10 4.56 41-9 4.11 37-9
41-10 4 41-10 3 41-9 4 41-9 3 39-8 4 41-8 4
CHRYSLER 8.25" & 8.375"
• 11-3/8’’, Oval cover 10 holes,
10 bolt, 8.250’’ diameter ring gear, 1.626’’ diameter pinion, 27 splines.
• Fits: 73-97 Cars, various passenger;
69-Present B100, B150, B200, B250;
66-97 B, D, W100; 66-97 B, D, W200;
66-97 B, D, W300; 76-80 Aspen, Volare; 70-74 Barracuda, Challenger; 73-76 Charger, Coronet; 72-79 Chrysler 300; 75-83 Cordoba; 82-Present Dakota; 72-76 Dart; 77-83 Diplomat, LeBaron; 72-88 Fifth Avenue, New Yorker; 81-83 Imperial; 70-81 Fury; 78-83 Mirada, Magnum; 72-73 Newport; 70-74 Polara, Satelite; 79-81 St. Regis; 86-Present W100, W150.
• 1.625’’ pinion diameter, 30 spline pinion, ‘’C’’ axle only. • 3-series fits 3.07 to 3.73 ratio carrier.
• 4-Series fits 3.90 and numerically higher carrier.
• Fits: 65-72 Bel Air/Caprice/Impala/Chevelle/El Camino/
Chevy II, 67-72 Camaro, 70-72 Nova/GTO/Firebird, 68-69 Olds F-85.
Part# Ratio
Street Gear
RIC49-0094-1 3.08
RIC49-0113-1 3.42
RIC49-0095-1 3.55
RIC49-0039-1 3.73
RIC49-0096-1 3.73
RIC49-0040-1 3.90
Street/Strip Gears
RIC69-0304-1 4.10
RIC69-0031-1 4.10
Street/Strip Gears
RIC69-0378-1 4.33
RIC69-0306-1 4.56
RIC69-0032-1 4.56
RIC69-0308-1 4.88
RIC69-0033-1 4.88
RIC69-0034-1 5.14
RIC69-0035-1 5.38
RIC69-0038-1 6.14
*Special Cross Shaft Pin Required RIC80-0269
When installing 5.14 to 6.14 ratios, differential pin P/N 80-0269-1 must be used.
Teeth Carrier
41-10 3
40-13 3 41.12 3 39-11 3 41-11 3 41-11 4 39-10 3
Part# Ratio Street/Strip Gear RIC49-0076-1 3.55
Teeth
39-11
41-10
4
CHRYSLER 8.75", 489 CASTING
• 8.750’’ diameter ring gear, 1.875’’ tapered pinion diameter, 10 spline pinion.
• Fits: 69-73 Chrysler, Dodge, Plymouth.
39-9
41-9 3
4
41-9 39-8 39-8 36-7 43-8 43-7
4 3 4 4 4 4
Part# Street/Strip Gear RIC69-0371-1 RIC69-0058-1 RIC69-0059-1 RIC69-0060-1 RIC69-0061-1 RIC69-0062-1
Ratio Teeth
3.55 39-11 3.91 43-11 4.10 41-10 4.30 43-10 4.57 32-7 4.86 34-7
511